A Review on Orthopaedic Biomaterials: Properties, Advances, and Future Directions

Shailja  Singh; Manvendra Singh Khatri

doi:10.61343/jcm.v3i02.126

Authors

Shailja Singh Department of Physics, National Institute of Technology Uttarakhand, Srinagar (Garhwal), Uttarakhand- 246174, India
Manvendra Singh Khatri Department of Physics, National Institute of Technology Uttarakhand, Srinagar (Garhwal), Uttarakhand- 246174, India

DOI:

https://doi.org/10.61343/jcm.v3i02.126

Keywords:

Biomaterials, Orthopaedics, Tissue Engineering, Osseointegration, Prosthetics, Scaffolds, Cytotoxicity

Abstract

Orthopaedic biomaterials play a pivotal role in advancing fracture fixation, joint replacement, and dynamic stabilization within orthopaedic applications. Primarily composed of metals, these biomaterials exhibit outstanding properties including high strength, ductility, fracture toughness, hardness, corrosion resistance, durability, and biocompatibility. Despite their versatility, the landscape of orthopaedic implant materials remains dominated by a limited range of metals, ceramics, composites and polymers. However, the durability of these implants is challenged by biological reactions and material degradation caused by wear and electrochemical corrosion. This article examines the developments that have taken place with respect to the biomaterials and their applications in implants in orthopaedic surgery. This encompasses history, types and properties of metals, polymers, ceramics, composite biomaterials, and processes of fabricating them. The characteristics like biocompatibility, mechanical properties, fluid stability, and the ability to induce osseointegration and the relevance of such materials for implants in orthopaedic surgery is also discussed in this article. Special attention is given to the development of novel bioactive metallic materials and their means of improving wear resistance and biocompatibility by changing the surface and applying coats. The scope of the review further covers advanced technologies including smart bio-materials, 3D/4D printing, use of nanotechnology, and prosthetics. Further, the review article discusses the current status and future trends concerning materials for orthopaedic surgery in greater detail.

References

Q Chen and G A Thouas, “Metallic implant biomaterials”, Materials Science and Engineering: R: Reports, 87:1-57, 2015.

M Navarro, A Michiardi, O Castano and J A Planell. JR Soc. Interface, 5: 1137-1158, 2008.

M Niinomi, T Narushima and M Nakai, “Advances in metallic biomaterials”, Heidelberg, DE: Springer, 2015.

A Bruinink and R Luginbuehl, “Evaluation of biocompatibility using in vitro methods: Interpretation and limitations”, Tissue Engineering III: Cell-Surface Interactions for Tissue Culture,117-152, 2012.

W H De Jong, J W Carraway and R E Geertsma, “In vivo and in vitro testing for the biological safety evaluation of biomaterials and medical devices”, In Biocompatibility and performance of medical devices. Woodhead Publishing, 123-166, 2020.

M N Helmus, D F Gibbons and D Cebon, “Biocompatibility: meeting a key functional requirement of next-generation medical devices”, Toxicologic pathology, 36(1): 70-80, 2008.

W Jin and P K Chu, “Orthopedic implants”, Encyclopedia of biomedical engineering, 1(3): 425-439, 2019.

F Findik, “Latest progress on tribological properties of industrial materials”, Materials & Design, 57: 218-244, 2014.

S Tkachenko, et al. “Wear and friction properties of experimental Ti–Si–Zr alloys for biomedical applications”, Journal of the mechanical behavior of biomedical materials, 39: 61-72, 2014.

H F Li, J Y Huang, G C Lin and P Y Wang, “Recent advances in tribological and wear properties of biomedical metallic materials”, Rare Metals, 40(11): 3091-3106, 2021.

S Parithimarkalaignan and T V Padmanabhan, “Osseointegration: an update”, The Journal of Indian Prosthodontic Society, 13(1): 2-6, 2013.

G R M Matos, “Surface roughness of dental implant and osseointegration”, Journal of maxillofacial and oral surgery, 20: 1-4, 2021.

T Albrektsson and A Wennerberg, “On osseointegration in relation to implant surfaces”, Clinical implant dentistry and related research, 21: 4-7, 2019.

A J Festas, A Ramos and J P Davim, “Medical devices biomaterials–A review”, Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 234(1): 218-228, 2020.

X Duan, et al. “Research progress of metal biomaterials with potential applications as cardiovascular stents and their surface treatment methods to improve biocompatibility”, Heliyon, 10(4), 2024.

G Szczęsny, et al. “A review on biomaterials for orthopaedic surgery and traumatology: from past to present”, Materials, 15(10): 3622, 2022.

D Pathote, D Jaiswal, V Singh and C K Behera, “Optimization of electrochemical corrosion behavior of 316L stainless steel as an effective biomaterial for orthopedic applications”, Materials today: proceedings, 57: 265-269, 2022.

C Morsiya, “A review on parameters affecting properties of biomaterial SS 316L”, Australian Journal of Mechanical Engineering, 20(3): 803-813, 2022.

P E Lushchik, et al. “Co-Cr alloys for biocompatible medical products”, In E3S web of conferences (Vol. 452, p. 05015). EDP Sciences, 2023.

P Pesode and S Barve, “A review-metastable β titanium alloy for biomedical applications”, Journal of Engineering and Applied Science, 70(1): 25, 2023.

Y Chen, J Dou, H Yuand C Chen, “Degradable magnesium-based alloys for biomedical applications: The role of critical alloying elements”, Journal of Biomaterials Applications, 33(10): 1348-1372, 2019.

S Virtanen, “Biodegradable Mg and Mg alloys: Corrosion and biocompatibility”, Materials Science and Engineering: B, 176(20): 1600-1608, 2011.

Y Song, S Zhang, J Li, C Zhao and X Zhang, “Electrodeposition of Ca–P coatings on biodegradable Mg alloy: in vitro biomineralization behavior”, Acta Biomaterialia, 6(5): 1736-1742, 2010.

M J Kasser, “Regulation of UHMWPE biomaterials in total hip arthroplasty”, Journal of Biomedical Materials Research Part B: Applied Biomaterials, 101(3): 400-406, 2013.

S M Kurtz and J N Devine, “PEEK biomaterials in trauma, orthopaedic, and spinal implants”, Biomaterials, 28(32): 4845-4869, 2007.

K L Ong, B M Yun and J B White, “New biomaterials for orthopaedic implants”, Orthopaedic Research and Reviews: 107-130, 2015.

S Punj, J Singh and K J C I Singh, “Ceramic biomaterials: Properties, state of the art and future prospectives”, Ceramics International, 47(20): 28059-28074, 2021.

P Dalla Pria, “Evolution and new application of the alumina ceramics in joint replacement”, European Journal of Orthopaedic Surgery & Traumatology, 17(3): 253-256, 2007.

M Bohner, “Bioresorbable ceramics”, Degradation rate of bioresorbable materials: 95-114, 2008.

M K Egbo, “A fundamental review on composite materials and some of their applications in biomedical engineering”, Journal of King Saud University-Engineering Sciences, 33(8): 557-568, 2021.

S Murugan and S R Parcha, “Fabrication techniques involved in developing the composite scaffolds PCL/HA nanoparticles for bone tissue engineering applications”, Journal of Materials Science: Materials in Medicine, 32(8): 93, 2023.

A Prasad, M R Sankar and V Katiyar, “State of art on solvent casting particulate leaching method for orthopaedic scaffolds fabrication”, Materials Today: Proceedings, 4(2): 898-907, 2017.

E Babaie and S B Bhaduri, “Fabrication aspects of porous biomaterials in orthopaedic applications: A review”, ACS Biomaterials Science & Engineering, 4(1): 1-39, 2018.

Q Song, S Prabakaran, J Duan, M Jeyaraj, S Mickymaray, A Paramasivam and M Rajan, M, “Enhanced bone tissue regeneration via bioactive electro spun fibrous composite coated titanium orthopaedic implant”, International Journal of Pharmaceutics, 607: 120961, 2021.

M Meng, J Wang, H Huang, X Liu, J Zhang and Z Li. “3D printing metal implants in orthopaedic surgery: methods, applications and future prospects”, Journal of orthopaedic translation, 42: 94-112, 2023.

F Yang, X Qu, W Cui, J Bei, F Yu, S Lu and S Wang, “Manufacturing and morphology structure of polylactide-type microtubules orientation-structured scaffolds”, Biomaterials, 27 (28): 4923-4933, 2006.

J R Smith, D A Lamprou, C Larson and S J Upson, “Biomedical applications of polymer and ceramic coatings: a review of recent developments”, Transactions of the IMF, 100(1): 25-35, 2022.

R Maurya, A R Siddiqui and K Balani, “In vitro degradation and biomineralization ability of hydroxyapatite coated Mg-9Li-7Al-1Sn and Mg-9Li-5Al-3Sn-1Zn alloys”, Surface and Coatings Technology, 325: 65-74, 2017.

C Hachimi Alaoui and A Fatimi, “A 20-year patent review and innovation trends on hydrogel-based coatings used for medical device bio fabrication”, Journal of Biomaterials Science, Polymer Edition, 34(9): 1255-1273, 2023.

H Chen, et al. “Progress in surface modification of titanium implants by hydrogel coatings”, Gels, 9(5): 423, 2023.

L Zhao, et al. “Antibacterial nano-structured titania coating incorporated with silver nanoparticles”, Biomaterials, 32(24): 5706-5716, 2011.

C L Romanò, et al. “Antibacterial coating of implants in orthopaedics and trauma: a classification proposal in an evolving panorama”, Journal of orthopaedic surgery and research, 10: 1-11, 2015.

S Lopez-Esteban, et al. “Bioactive glass coatings for orthopedic metallic implants”, Journal of the European Ceramic Society, 23(15): 2921-2930, 2003.

S Devgan and SS Sidhu, “Evolution of surface modification trends in bone related biomaterials: A review”, Materials Chemistry and Physics, 233: 68-78, 2019.

T Lu, Y Qiao and X Liu, “Surface modification of biomaterials using plasma immersion ion implantation and deposition”, Interface focus, 2(3): 325-336, 2012.

W Sun, W Liu, Z Wu and H Chen, “Chemical surface modification of polymeric biomaterials for biomedical applications”, Macromolecular Rapid Communications, 41(8), p.1900430, 2020.

B K M B Alemu Reta and T Tesfaye, “Smart and intelligent biomaterials for novel applications–a review”, International Journal of Polymeric Materials and Polymeric Biomaterials, 74(2): 140-158, 2025.

C Shen and A Shen, “4D printing: innovative solutions and technological advances in orthopedic repair and reconstruction, personalized treatment and drug delivery”, BioMedical Engineering OnLine, 24(1): 5, 2025.

E Yarali, et al. “4D printing for biomedical applications”, Advanced Materials, 36(31): 2402301, 2024.

J Yazdani, et al. “A short view on nanohydroxyapatite as coating of dental implants”, Biomedicine & Pharmacotherapy, 105: 553-557, 2018.

S Kumar, et al. “Nanotechnology-based biomaterials for orthopaedic applications: Recent advances and future prospects”, Materials science and engineering: C, 106: 110154, 2020.

W Liang, et al. “Current developments and future perspectives of nanotechnology in orthopaedic implants: an updated review”, Frontiers in Bioengineering and Biotechnology, 12: 1342340, 2024.

Y Lu. “Toward fully automated personalized orthopedic treatments: innovations and interdisciplinary gaps”, Bioengineering, 11(8): 817, 2024.

M Kouhi, et al. “Recent advances in additive manufacturing of patient-specific devices for dental and maxillofacial rehabilitation”, Dental Materials, 2024.